Part 1Preliminary1Short titleThis regulation may be cited as the Fisheries Legislation Amendment Regulation 2026.2CommencementPart 3 commences on 1 July 2026.Part 2Amendment of Fisheries (Commercial Fisheries) Regulation 20193Regulation amendedThis part amends the Fisheries (Commercial Fisheries) Regulation 2019.4Insertion of new sch 2, s 103ASchedule 2, after section 103—insert—103A Tom’s fisheye(1)An opening, commonly known as a Tom’s fisheye, in a net is a recognised BRD if the opening complies with this section.(2)The opening must be—

(a)held open by a rigid frame that consists of—

(i)a hexagon-shaped external frame; and

(ii)a V-shaped external frame; and

(iii)a cone-shaped insert; and

(b)no more than 70 meshes from the cod end drawstrings of the net.

(3)The rigid frame must be installed so that the apex of the V-shaped external frame points towards the mouth of the net.(4)The hexagon-shaped external frame must be—

(a)at least—

(i)360mm wide; and

(ii)200mm high; and

(b)attached—

(i)by a rigid bar from the top midpoint of the hexagon-shaped external frame to the top midpoint of the cone-shaped insert; and

(ii)by a rigid bar from the bottom midpoint of the hexagon-shaped external frame to the bottom midpoint of the cone-shaped insert.

(5)The widest point of the V-shaped external frame must be—

(a)equal to the width of the hexagon-shaped external frame; and

(b)attached, perpendicularly, to the widest part of the hexagon-shaped external frame.

(6)The cone-shaped insert must be—

(a)at least—

(i)340mm wide; and

(ii)185mm high; and

(iii)290mm long; and

(b)attached—

(i)by a rigid bar from a point on the left side of the cone-shaped insert, no more than 100mm from the open end of the insert, to the left arm of the V-shaped external frame with a gap of at least 20mm between the insert and the frame; and

(ii)by a rigid bar from a point on the right side of the cone-shaped insert, no more than 100mm from the open end of the insert, to the right arm of the V-shaped external frame with a gap of at least 20mm between the insert and the frame; and

(iii)by a rigid bar from the midpoint of the back of the cone-shaped insert to the apex of the V-shaped external frame with a gap of at least 29mm between the insert and the frame.

(7)There must be a gap of at least 94mm between the top side of the hexagon-shaped frame and the top side of the cone-shaped insert.(8)During trawling, nothing must cover any part of the opening.Part 3Amendment of Fisheries (General) Regulation 20195Regulation amendedThis part amends the Fisheries (General) Regulation 2019.6Amendment of sch 3 (Declared fish habitat areas)Schedule 3, entry for Bowling Green Bay FHA–007—omit, insert—Bowling Green Bay FHA–007 (revision 1)The declared fish habitat area excludes the following—•land within the following lots that is not tidal land—•lot 2 on plan USL38596 (Bray Islet)•lot 3 on plan USL38596 (Bare Islet)•lot 4 on plan USL38596 (Bald Islet)•the area bounded by a 75m radius circle with the centre point at latitude 19°16.26714' south, longitude 147°03.77034' east. 7Amendment of sch 8, s 18 (Meaning of prescribed stocked impoundment)(1)Schedule 8, section 18(1), entry for Beehive Dam—omit.(2)Schedule 8, section 18(1)—insert—

•Enoggera Reservoir

•Mount Morgan Water Supply - No. 7 Dam

•Paradise Dam